Difference between revisions of "Gaggia Anima Prestige"

Revision as of 12:05, 26 October 2017 (view source) Ed (Talk | contribs) ← Older edit		Revision as of 13:50, 19 January 2018 (view source) Ed (Talk | contribs) Newer edit →
Line 91:		Line 91:
	{{Maintenance-Gaggia-Super-Automatic}}		{{Maintenance-Gaggia-Super-Automatic}}
		+	{{Maintenance-Gaggia-Super-Draining-Boiler
		+	|Anima =
		+
		+	Also, on Anima models, you can enter the “TECH MENU” on the machine.
		+
		+	#'''Start by turning off the main power from the back of the machine.''' Press and hold ESPRESSO and MENU at the same time. Hold them down and turn the main power from the back of the machine back on. The screen should now say FW on the top. This stands for FIRMWARE, and you are now in the tech menu. The center button below the screen is your standby button, but you may call it the power button. You can press this to navigate through the 6 menu options.
		+	#'''When you see BU at the top of the page, you are on the BREW UNIT page.''' Press and hold ESPRESSO. You should hear the brew unit going into “WORK” position. It will come to a stop, and that’s when you can let go of the ESPRESSO button. YOU MUST HAVE THE BREW UNIT IN WORK POSITION IN ORDER FOR WATER TO COME OUT OF THE FRONT OF THE MACHINE. Press the standby/power button again, so that you navigate to the PUMP page.
		+	#'''You will see something on the left called EV1.''' This stands for Electromagnetic Valve. It’s basically a solenoid valve that opens and closes and lets water flow either out of the steam wand or out of the group head.
		+	#*When EV1 is OFF - Press the Steam button- water should come out of the front coffee spouts of the machine.
		+	#*When EV1 is ON- Press the Steam button, and water will come out of the steam wand. You want to pour water out of the steam wand until you hear the machine sputter. When you hear this, the boiler is completely drained.
		+	#'''REMEMBER TO GO BACK TO THE BU PAGE, AND PUT THE BREW UNIT BACK INTO HOME POSITION. THIS IS DONE BY PRESSING AND HOLDING THE AROMA STRENGTH BUTTON UNTIL THE BREW UNIT COMES TO A STOP '''
		+
		+	}}
	{{Maintenance-Super-With-Carafe		{{Maintenance-Super-With-Carafe

---

Revision as of 13:50, 19 January 2018

The Gaggia Anima Prestige is a super-automatic espresso machine that features beverage programming and an auto-frothing carafe.

Gaggia Anima Prestige
Manufacturer: Gaggia
Model Name: Anima Prestige
Model Number: RI8762
Type: Super-Automatic

Machine Set-Up/New Users

There are some key differences in how Super-Automatic machines work in comparison to semi-automatic/manual units to be aware of before the first use. Having a working knowledge of the machine before using it will help ensure a satisfying experience, increase the longevity of the unit, and prevent possible issues/damage that can result from misuse. This information in this section will cover machine set up and basic use. To start, the video below provides supplemental start-up information for the material covered in this section:

Bean Compatibility

Before going into the set up of the machine it's best to review this topic because of its importance. The most important thing to understand about Super-Automatic machines is that they do not accept oily, caramelized, or flavored beans. The video below discusses what beans are compatible, and what beans are not:

First Time Use

The machine manual provides a thorough walk-through of the set-up of the unit, but there's so much information it can be mystifying. In this section we will walk you through the most important points of the machine setup.

Initial Setup/Priming

If you’re running into issues having your machine prime, you will want to follow these steps to help get the machine primed.

1. With the machine off, press and hold the top left button (espresso) and the bottom right button (menu) at the same time and power on the machine. This should put you in programming mode.
2. Once the machine has come up and displays FW at the top, you can release the buttons.
3. From here, you will press the middle power/standby button 4 times to get to the valve/pump test screen. It should display EV in the top left, and PUMP in the top right.
4. From this screen we can now manually run the pump on the machine. Place a cup under the steam arm, and press the button on the top left (espresso) - you should see EV1 OFF switch to EV1 ON. Once it displays EV1 ON, you can press the top right button (steam), to run the pump. It may take a few seconds, but water should now come out of the steam wand.
5. Rinse and repeat the process of turning on and off the pump for a few seconds. This should force water to be run through the machine.
6. Once completed or run thoroughly, turn the machine off and back on to exit programming mode. Check to see if the error has cleared.

Beans/Grinder Set-Up

After the machine has been successfully primed it is important to set the grinder for initial use. The machine's manual indicates that adjustments for the grinder should only be made while the grinder is running. While this is technically true, the sensor for the bean hopper sensor prevents adjustments from being made, because the grinder will turn off if the machine senses the hopper lid is open. This sensor is an additional safety feature for the U.S. version of the machine to prevent exposure to active grinder burrs; the manual does not reflect this change.

There are two ways to work around this issue. Another magnet can be placed on the hopper sensor so that the machine can be run with the lid open. The magnet should be placed in the socket pictured below in order to trip the sensor:

Alternatively the grinder can be adjusted in small increments. Move the adjustment knob 1 tick, grind a shot, and then move it another tick. Do this until you are at the desired grind setting. This will ensure that any grinds or bean fragments are swept out of the way before the burr plates are moved closer together.

1. For initial use the grinder should be set to the coarsest grind setting, which will be the largest number/dot on the grinder knob. Once the dial is set you can add the beans in; make sure to only add dry beans as prescribed in the Bean Compatibility section. Since the grinder is being adjusted to a coarser setting the grinder does not need to be running.
2. Set the aroma to the maximum setting using the aroma adjustment button. This increases how much the grinder grinds each time. This will help the grinder mechanism fill with beans/grounds faster for the next step.
3. Next choose one of the brewing options. The first few shots of the machine may come out watery/weak -- this is to be expected since the beans need to feed into the grinder, and the bypass chamber needs to fill. Depending on the machine/type of bean used it can take up to 5-10 attempts.
4. Once shots are pouring through consistently then settings can be adjusted. Adjustments are covered in the next section.

Drink Adjustment

The machine is now ready to brew for drinks, but the startup settings may not match the drink you are trying to brew. For the demonstration purposes this section will walk through brewing a single shot espresso from the machine.

1. Set the machine to the three bean aroma setting using the aroma/preground button. This full aroma setting is typically best for espresso extraction, but can be lowered if the coffee is too strong.
2. Adjust the fineness dial down to the finest grind setting, which is the smallest dot on the unit. As discussed in the previous section, adjustments in the finer direction should be made gradually. Adjust the grinder down 1 dot at a time, brewing a shot in between each adjustment. This prevents clogging/damage to the unit.
3. Most Super-Automatic machines come programmed to 1.5-2 oz. for the espresso option despite being single shot machines. For best results we suggest reprogramming the shot size to 1 oz. Shot sizes can be easily reprogrammed on this unit by pressing and holding the drink button you would like to reprogram. Hold the button for at least 5 seconds until the grinder activates and then let go. The machine will indicate it is in programming mode on the screen. Use a measuring device to measure the liquid volume being dispensed. Once you have 1 oz. in the measuring device press the checkmark (aroma/preground) button to stop the shot and save the new option.
4. One really important thing to consider for this machine is that it uses a smart grinder. Smart grinders make gradual adjustments to how the beans are ground and how much coffee is dosed each shot. After an adjustment is made the machine will typically take 10-15 shots for best results. The grinder will make gradual changes based on the new adjustment to improve the flavor of the coffee each time. For this same reason constant adjustments should not be made to the machine, as the smart grinder will not have enough time to respond to the adjustments.
5. The video below discusses how to adjust for other types of drinks. The general rule of thumb is that the more liquid volume passed through the grinds the coarser the grind should be set in order to get a balanced extraction.

Puck Consistency

A large misconception is that super-automatic machines should have a dry coffee puck after the machine is finished brewing. While this is true of other styles of espresso machine, this is not true of a super-automatic unit. Super-automatic machines utilize heat and pressure as part of the brewing process, which is key to espresso brewing. The machine achieves this through a device called a brew unit. The brew unit uses a similar but different brewing process to a semi-automatic or prosumer style machine. As a result the pucks will not always come out firm and dry. They may come out muddy or broken. This is perfectly normal; the machine will still produce a good extraction that contains crema and tastes good.

Bypass Doser

If you plan on using the bypass doser function on the machine to brew with pre-ground coffee there are a few things to consider for the best brewing experience:

1. The bypass doser will only accept 8-9 grams of coffee at a time. The scoop that comes with the machine is merely for transferring coffee grinds, it is not a measurement tool. To prevent overfilling the bypass doser we suggest using a level scoop, and then taking a large pinch out of it. A little bit less than a full scoop is the perfect amount.
2. Make sure to use the aroma button to activate the preground mode before beginning the brew, otherwise the machine will also grind coffee, which will result in too much coffee going into the brew unit and the machine will abort the brew.
3. If the coffee is ground too coarsely the resulting shot is going to taste sour, weak or watery. Coarsely ground coffee also does not compact well, so the machine may dump the coffee if the grind is to coarse. Coffee ground for espresso should be slightly finer than table sugar or sand.
4. Alternatively it is also possible to have coffee that is ground too fine. Extremely fine grinds can result in little or no flow from the machine, and very bitter shots. Coffee that is ground too finely can cause blockages in the system that can only be resolved through deep cleaning or a repair.

Do not add whole beans, or entire bags of preground coffee into this chamber. It can cause irreversible damage to the machine's brewing assembly.

One useful trick the the bypass function allows for is that you can do a quick rinse of the brew circuit by simply running a bypass cycle and not adding any preground coffee. This will let plain water flow through the brew circuit which will remove old coffee flavors, oils, and grounds. You may want to do this if you've recently switched beans to remove some of the old flavors.

Brew Unit/Pump Noises

When Super-Automatic machines are in operation the brew unit will make a few different noises which are normal. The brew unit will make several loud clicking noises through the duration of the brewing cycle. These loud clicking noises are perfectly normal and will not harm the machine. The brew unit function is monitored by sensors to prevent it from being overloaded, so it cannot break itself apart.

The brew unit can also make squeaking noises during its operation. The squeaking could be from o-rings sealing on the brew unit, or the brew unit parts sliding along the tracks. If you are hearing more squeaking than normal it may be a sign that the brew unit needs to be cleaned and lubricated. Some squeaking is also normal on very new units as there are o-rings/seals that need some time to wear in.

When the pump of the machine activated for brewing, refilling, and hot water dispensing it is going to make a loud humming noise. The machine utilizes a vibration style pump. This style pump produces high pressures despite being compact. The pump achieves this through rapid vibration of internal parts, which produces a loud humming noise.

Mavea Intenza Filter

Once set-up has been fully completed the filter can be installed. Installing the filter beforehand could cause the machine to become vapor locked and require manual priming. Follow the instructions on the filter packaging before installing it. Within the machine menu is an option for activating and installing the filter. If you use this activation menu option for the filter the machine will automatically remind you when the filter needs to be replaced. Instructions for activating this function can be found in the machine manual. The filter's packaging instructions will indicate the filter needs to be activated by soaking in water before it is installed. If the machine gives a priming error when the filter is installed simply remove the filter and soak in warm water upside down for at least an hour and then reinstall it.

Cleaning & Maintenance

Proper machine maintenance is critical to proper machine functionality. Most machine failures are caused by a lack of cleaning and maintenance. This is vital, as many manufacturer warranties do not cover cleaning/maintenance related breakdowns. To avoid this, it is imperative to keep a regular maintenance schedule. Consult pp. 36-53 in your machine manual for fully detailed cleaning procedures, including descaling, carafe cleaning, and brew group cleaning, as well as the recommended products for machine maintenance. Listed below is a suggested maintenance rundown for most super-automatic espresso machines:

Machine Maintenance

Descaling

Descaling the machine should be done on a bimonthly basis using the product recommended by the manufacturer. Descaling is still required even if reverse osmosis, distilled, or zero water is being used. Refer to your machine manual for specific instructions for this unit.

Brew Unit

The brew unit of the machine should be removed on a weekly basis and rinsed off with cold water. Cold water must be used because hot water can wash away the lubricant that coats the moving parts of the brew unit. It is also important to use plain water; detergents and soaps should not be used. While the brew unit is removed, the brew unit chamber should be wiped down with a moist cloth to remove excess grounds and coffee residues.

Your machine features a brew unit cleaning cycle. This should be done on a monthly basis; refer to your manual for instructions on how to run one.

A complete disassembly, cleaning, and lubrication of the brew unit should be done every 500 cups or every 6 months, whichever comes first. A food safe silicone-based lubricant should be used, such as food grade Petrol-Gel.

Steam Wand Cleaning

Steam wands and nozzle attachments should be cleaned daily, after the machine is finished for the day. Milk residues quickly build up in steam wands and frothing nozzles, so it is important to keep these clean to prevent blockages from forming.

Recommended Cleaning Products

The best descaling product for this machine is Durgol Swiss Espresso Descaler. The suggested tablets for running brew unit cleaning cycles are the Gaggia Coffee Clean Tablets or Urnex Full Circle Espresso Machine Cleaning Tablets.

Draining the Boiler

Be sure to drain the boiler(s) whenever you ship or store your machine, as water can freeze and expand inside. This can lead to cracking, fracturing, or otherwise damaging the boiler unnecessarily. The video below shows you how to do this.

Also, on Anima models, you can enter the “TECH MENU” on the machine.

1. Start by turning off the main power from the back of the machine. Press and hold ESPRESSO and MENU at the same time. Hold them down and turn the main power from the back of the machine back on. The screen should now say FW on the top. This stands for FIRMWARE, and you are now in the tech menu. The center button below the screen is your standby button, but you may call it the power button. You can press this to navigate through the 6 menu options.
2. When you see BU at the top of the page, you are on the BREW UNIT page. Press and hold ESPRESSO. You should hear the brew unit going into “WORK” position. It will come to a stop, and that’s when you can let go of the ESPRESSO button. YOU MUST HAVE THE BREW UNIT IN WORK POSITION IN ORDER FOR WATER TO COME OUT OF THE FRONT OF THE MACHINE. Press the standby/power button again, so that you navigate to the PUMP page.
3. You will see something on the left called EV1. This stands for Electromagnetic Valve. It’s basically a solenoid valve that opens and closes and lets water flow either out of the steam wand or out of the group head.
   • When EV1 is OFF - Press the Steam button- water should come out of the front coffee spouts of the machine.
   • When EV1 is ON- Press the Steam button, and water will come out of the steam wand. You want to pour water out of the steam wand until you hear the machine sputter. When you hear this, the boiler is completely drained.
4. REMEMBER TO GO BACK TO THE BU PAGE, AND PUT THE BREW UNIT BACK INTO HOME POSITION. THIS IS DONE BY PRESSING AND HOLDING THE AROMA STRENGTH BUTTON UNTIL THE BREW UNIT COMES TO A STOP

Milk Carafe Maintenance

Automatic Cleaning Cycle

The automatic carafe cleaning cycle for this machine should be completed on a weekly basis. It is important to keep the carafe clean in order for the carafe to function properly and to be able to produce froth. Unsanitary milk residues can build up in the carafe if it is not maintained properly. Instructions for starting a full cleaning cycle of the Milk Carafe can be found on pp.16-17 of the machine manual.

Manual Disassembly & Cleaning

While the automatic cleaning cycle does remove most residues it is not a complete cleaning of the carafe. The carafe should be pulled apart on a daily basis, after you are finished making latte drinks for the day, for more thorough cleaning. Instructions for manually disassembling and cleaning the milk carafe can be found on p.17 of the machine manual.

Recommended Cleaning Products

The automated carafe cleaning cycle requires the use of a cleaning solution intended for removing milk residues. The recommended product for this unit is The recommended cleaning solution for the milk carafe is Urnex Rinza..

Troubleshooting

No Crema or Bad Tasting Shots

Appropriately adjusting the grinder is also important. Poor shots can also be the result of incorrect grind settings.

1. If the shot is too bitter:
   1. The grind is set too fine. Try adjusting the grind to a coarser setting, typically indicated by a large dot symbol or higher number.
   2. If applicable, the aroma setting is set too high. Lower the aroma setting so that less coffee is ground per shot.
   3. The beans being used are over-roasted, and a lighter roast is needed.
2. If the shot is too sour or weak tasting:
   1. The grind is set too coarse. Try adjusting the grind to a finer setting, indicated by a lower number. Whenever moving the grind to a finer setting it is important to make minor adjustments, and to only adjust the grinder while in operation.
3. If there is little crema:
   1. The beans are probably stale and fresher beans need to be used.
   2. The grind setting does not match the drink that is being made. Smaller drinks such as an espresso require finer grind size; larger drinks such as a longo require a coarser grind.
   3. Oily or dark roasted beans are being used. These beans are not compatible with the unit, and are not suitable for espresso brewing. The oils and chemicals that are needed to produce a rich crema have been roasted out of the bean. Switch to a drier/lighter roast.
4. Keep the machine properly cleaned and maintained for good tasting shots. Your grinder may need to be cleaned or calibrated, or you may need to descale your machine to remove any unwanted residues or flavors.

Difficulty Frothing

Before going through the following steps make sure to try all of the cleaning any maintenance items indicated in the section of this article which discusses how to clean and maintain the milk carafe.

1. If there is nothing coming out of the carafe at all:
   1. Check the carafe to make sure it is securely attached to the machine and that the machine recognizes the carafe is in place.
   2. Make sure the carafe is properly assembled and the manual cleanings have been completed. Refer to pp. 16-17 of the owner's manual for instructions on how to clean the carafe and properly reassemble it. Inspect the parts to make sure none of them appear broken, damaged, or missing.
   3. The machine may not be producing steam. If the machine is displaying an E15 or steam thermostat error then the steam thermostat is broken and the machine will require a repair.
2. If the carafe is spitting or not producing foam:
   1. A non-compatible milk is being used. The machine is designed for use with whole or 2% milk, so the best results will be achieved by using these milks.
   2. Make sure the carafe is properly assembled. Refer to pp. 16-17 of the owner's manual for instructions on how to clean the carafe and properly reassemble it.

Flow Issues

The first place to start with any flow issue is cleaning the machine. Before going through these steps please make sure the machine is cleaned according to the Cleaning & Maintenance section of this article.

Poor Or No Flow Or E05 Error

If you are not able to get water to flow through the machine at all, or if the machine displays an E05 code, then something is blocking water flow through the machine. This issue typically indicates the machine is not being cleaned on a regular basis. Review the cleaning & maintenance rundown for this machine, and make sure maintenance is done at least as often as is suggested with the recommended product. Once flow is restored, even if it is minimal flow, a descaling should be done immediately.

1. The water tank is not seating properly. Please remove the tank and reinsert it firmly. Make sure there are no beans or debris beneath the water tank preventing it from seating flush with the machine.
2. If you are using an Intenza water filter in the machine then it might be blocking the flow of water. Try removing the water filter and using the machine without it. If the machine works without the water filter, then the filter was blocking the flow of water. Keep the filter out of the machine for the remaining steps.
3. Debris has been drawn into the system from the water tank. This kind of debris can get lodged in valves/water circuits and cause flow issues.
   • Try cleaning the brew unit check valve using the instructions here.
4. If you have been able to restore some flow to the brew circuit, a brew unit cleaning cycle should be completed. The process can be found on pp. 49 of the machine manual.

No Flow From Milk Carafe Or Hot Water Nozzle

Once the flow issue has been resolved the machine should be immediately descaled with the recommended product and a carafe cleaning cycle should be run. Flow issues and blockages are typically due to lack of maintenance or excessive scale buildup. Also refer to the section of this article which discusses milk carafe issues before proceeding.

1. If the milk carafe is attached remove it from the machine and attach the hot water nozzle to the milk carafe port. Set the machine to the hot water dispensing mode. The machine should now begin to heat up, and a thermostat icon will appear on the screen.
   1. If the machine gets stuck on the thermostat icon for a long period of time or the machine gives an E15 error the machine will require a repair; one of the thermostats has gone bad.
   2. If the machine heats up properly you should hear the pump start to vibrate.
2. Once the pump is activated hot water should begin to flow through the nozzle. If hot water flows through the nozzle stop the machine from dispensing hot water and try using the milk carafe again. There may have been a piece of debris in the steaming circuit which the hot water function dislodged.

Reduced Or No Flow During Brewing

1. If there is no flow while brewing specifically, then something is blocked along the brew circuit. Begin by running a descale of the machine using the recommended product. Scale buildup is the most common cause of flow issues. Descaling will most likely resolve the issue.
2. If the machine is set to a really fine grind, the grinds can block the flow. Set the grind to a coarser setting and see if flow is restored. Leave the grind on the coarse setting for the remainder of flow testing.
3. There may be an issue with the brew unit.
   1. First remove the unit and rinse it off with cold water. Do not use any sort of detergent or soap to rinse it off or necessary lubricant will be removed.
   2. Wipe down the brew unit chamber with a damp cloth to remove any leftover grounds. A microfiber cloth is best, to prevent any cloth fibers from remaining behind.
   3. Clean the check valve following these instructions.
   4. Reinsert the brew unit and test for flow.
4. This machine allows beverage length to be reprogrammed. Make sure it isn't set to the minimum brew length. If the machine is programmed to the minimum beverage length the machine may not dispense any coffee, or it may only dispense a few drops. Try reprogramming the machine to a longer length drink to see if it resolves the no flow issue.
5. Check the brew unit to make sure it is lining up with the spout assembly and connecting with the spout assembly properly.
6. If you are noticing a lot of brewed coffee or coffee sprayed inside the brew unit chamber then the brew unit o-ring may be damaged or out of place.
   1. Remove the brew unit and inspect the large red o-ring attached to the tamping assembly. Make sure it is clean, properly positioned, and not damaged.
   2. If the o-ring is broken or damaged it should be replaced. A brew unit o-ring can be purchased here.
7. Your machine features an e-plus dial which may be blocked. Try brewing a shot and while the pump is activated turn the e-plus dial back and forth. This may clear up the blockage and restore flow. E-plus dial is pictured right.
8. The dispensing spout may be blocked. Try very gently cleaning the dispensing spout holes with a toothpick to remove any blockages.
9. The selector valve may be blocked. Follow these cleaning instructions to clean it.

Have Flow But Getting No Flow Error

In some situations, you will be able to get flow through the machine for all functions, but the machine thinks there is no water flowing through. There is a device in the machine called a flow meter, and it tells the machine when water is flowing through or not. The device operates by having small fan-like blades spin when water passes through it. If those blades get stuck from excessive scale buildup or debris, then they will not spin. As a result, even though water is flowing through the machine, you will get a flow error.

If your machine uses a water filter, temporarily remove it from the water tank and add the recommended descaling product to the water tank. The descaler needs to work its way into the system to start dissolving the scale buildup in the flow meter. You may have to keep restarting the machine so that it can keep attempting to prime, which will draw the descaler/water solution into the system. If at any point you are able to clear the flow message then you will want to do an immediate descale of the machine. After you have descaled, run 4-5 tanks of plain water through the hot water function for the wand in order to ensure the system is completely free of debris.

Machine Is Leaking

From The Bottom

1. Check the internal drip tray and make sure it is not overfilling. If the drip tray full indicator came on, and the trip tray was removed and reinserted but never emptied, it will reset the machine sensor and possibly result in the tray overflowing.
2. The leaking is coming from the water tank chamber.
   1. If the water tank is not positioned properly it can cause water to continuously drain from the tank, even while the machine is turned off. This happens when the water tank is inserted far enough to open the release valve, but not far enough to seal with the intake line. This water can leak out from the water tank and end up on the bottom of the machine. This particular issue is usually indicated by lots of clear water leaking onto the counter or into the internal drip tray, even though the machine is powered off. Remove the water tank and make sure there isn't anything, such as coffee beans, which could be blocking the tank from seating properly and then firmly reinsert the tank into the machine and press firmly on it to make sure it creates a good seal with the intake line.
   2. If the machine only leaks while the water tank is attached, but is properly inserted, then the intake line may be broken or disconnected. This will require a repair.

   If this does not resolve the leaking, then the leaking may be coming from an internal component and the machine should be repaired.

Machine Not Heating Or Powering On

No Power

1. Make sure the machine is plugged into an appropriate power source.
   1. Do not use the machine on a surge protector. This machine has a high power draw, more than a typical kitchen appliance such as a refrigerator or a microwave. Surge protectors are typically not rated to handle the amperage this machine requires.
   2. Make sure the power cord is firmly inserted into the power socket on the machine.
   3. Try using the machine on a different outlet, and make sure the machine is the only appliance plugged into that outlet.
   4. Try testing another appliance on the same outlet.
2. Make sure the power switches are functioning properly and not broken. If the machine isn't powering on try pressing and holding the power button in the on position to see if the machine turns on. If you are able to power the machine on this way then the power switch needs to be replaced.
3. If the machine recently had a leak, had water spilled on it, or any other exposure to moisture then the machine may be shorting out. Try letting the machine sit unplugged for 48 hours to make sure there isn't a short caused by moisture.

Cold Shots or E14 Error

1. If the machine is producing shots that are hot, but you would like them to be hotter, check the beverage programming menu. Make sure all of the drinks are set to brew at the highest temperature.
2. Make sure you are using a preheated cup. Ceramic cups will sap a lot of heat from the shot resulting in a colder shot. Preheating the cups using the machine's hot water function will allow the cup a great deal more heat. Alternatively, you can brew into a paper, styrofoam, or other well insulated cup. This video explains the importance of a pre-heated cup during espresso brewing:
3. If the shots are completely cold, or the machine is displaying an E14 error code, then there is a thermostat issue. Try restarting the machine to resolve the issue. If the error code continues to appear, then the thermostat is damaged and the machine will need to be repaired.

---

Brew Temperature Comparison: Pre-heated vs. Room Temp Espresso Cups

No Beans, Grinder Blocked, Or E01

All three of these issues share the same root cause. The grinder has become jammed with grounds or coffee residues. These issues are typically a result of incorrect beans being used in the machine. This machine is not compatible with oily, dark roasted, caramelized, or flavored beans. Use of these beans can cause permanent damage to the machine that is not covered under warranty. These beans can be identified easily. They will be shiny and feel slippery or sticky. Dry beans that are appropriate for the machine will look dull and feel rough. This machine does not have a user serviceable grinder so it is very important that the correct beans are used. Follow these steps to fix the behavior:

1. Remove all of the beans and set them aside.
2. Move the grinder adjustment dial all the way to the coarsest setting.
3. Use a vacuum to thoroughly clean out the grinder. In particular vacuum down in the chute where the beans feed into the inside of the machine.
4. Clean out the dosing chute using the following instructions: here.
5. Add beans back into the machine. The beans must be dry beans. Do not add incompatible beans back into the unit. Make sure the grinder is still set to the coarsest setting.
6. Test the machine to see if it can successfully brew a shot. If it successfully brews, run 2-3 more shots on this grind setting so that we can be sure the system is free of the old coffee grounds.
7. Once the machine is functional on this setting you can begin adjusting the grind to your preferred setting. Make small, one-tick-at-a-time adjustments, and be sure to brew shots in between. This will prevent the machine from jamming again.

Bean Difference

Brew Unit Blocked, Stuck, or E03 or E04 Error Codes

The machine is sensing that the brew unit motor is working too hard to engage the brew unit. This is a fail-safe built into the machine to prevent itself from damaging the brew unit; the machine will stop working and display an error. This issue is typically resolved through normal maintenance.

First restart the machine to clear the error message and reset the brew unit back to the home position so that it can be removed. If the machine is in an active rinse cycle do not try to remove the brew unit. The rinse cycle must be completed before the brew unit can be removed.

• Try running a blank bypass shot. To do this just run a normal bypass shot but do not add any coffee. You should just have plain water come out of the spouts. If the machine successfully completes this cycle then we know it's a coffee issue. Refer to the section of this article that discusses grinding issues.
• If this happened when you were using the bypass function specifically, then you may have added too much pre-ground coffee. The machine only accepts about a maximum of 8-9 grams per shot. The scoop that comes with the machine doses more than this. To make sure you are adding the appropriate amount take one level scoop of pre-ground coffee and remove a large pinch from it. This should about about 8 grams of coffee and should work in the machine.

---

How to Remove Stuck Brew Group

• When the machine indicates that it is ready for use open the door to the brew unit chamber.

Try removing the brew unit. If the brew unit does not come out easily, do not force it out. The brew unit is stuck in an engaged position and will need to be properly reset. Forcing it out of the machine can break the brew unit and possibly cause damage other parts of the machine. Follow the instructions in the video below to reset the brew unit before moving on to the next step. If the brew unit won't reset to the home position, the motor that manipulates the brew unit may be damaged, and the machine may require a repair.

If the brew unit is easily removed then rinse it off with cold water and let it dry.

• The brew unit will need to be cleaned and lubricated.
• Reinsert the brew unit into the machine and try brewing a shot.

Too Much Steam/Milk Boiling

If you think your wand is producing too much steam, or your milk looks like it is boiling, then you may need to make an adjustment to your frothing technique. Boiling milk, or milk that is getting to hot before frothing is completed is an indication that incorrect frothing technique is being used. Review the section of this article that addresses frothing difficulties for more information.

If you have tried adjusting your technique and the wand still appears to be producing too much steam, then a steam test should be completed.

Steam Test Instructions

If the machine is within the specified steam test range, then the machine is producing the correct amount of steam and an adjustment to frothing technique is necessary. Using a carafe that is chilled in a freezer before frothing is helpful for keeping the milk cooler for longer, allowing for more time to froth before the milk begins to scald.

Diagrams & Manuals

Gaggia Anima Prestige
Anima Deluxe Error Codes and Troubleshooting:
Electrical Diagram:	Not Available
Hydraulic Diagram:	Not Available
Machine Manual:
Parts Diagram:
Service Manual
Startup Guide:	Not Available

Specifications

Basic Specs
Width:	8.7 in.
Height:	13.38 in.
Depth:	16.93 in.
Weight:	16 lbs
Watts:	1400
Volts:	120
Housing
Housing Material:	Stainless Steel/ABS Plastic
Bean Hopper Material:	Plastic
Drip Tray Material:	Plastic
Drip Tray Cover Material:	Stainless Steel
Drip Tray Capacity:	24 oz
Ground Coffee Container Material:	Plastic
Drain Line Adaptable:	No
Spend Coffee Capacity:	15
Easy To Rotate:	No
Tall Legs:	No
Power Cord Length:	48 in.
Cup Height
Adjustable Height:	Yes
Max Height:	5.9 in.
Min Height:	4.33 in.
One Touch Cappuccino
One Touch Capable:	Yes
One Touch Device:	Milk Carafe
Adjustable Froth Quality:	No
Height:	5.8 in.
Separate Steam Wand:	No
Programmable:	Yes
Milk Carafe Type:	Plastic Attachable
Self-Cleaning:	Yes
Dishwasher Safe:	No
Water Source
Reservoir or Plumbed:	Reservoir
Reservoir Capacity:	60 oz.
Reservoir Material:	Plastic
Reservoir Access:	Top
Reservoir Removable:	Yes
Water Filter:	Mavea Intenza
Water Level Visible:	No
Controls
Adjustable Coffee Strength:	Yes
Type of Controls:	Push Button
Display Type:	LCD
Programmable Brewing:	Yes
Temperature Control:	3 Settings
Adjustable Coffee Dosage:	Yes
Digital Display:	Yes
Clock/Timer:	No
Coffee Dosage Quantity:	6.5-11 grams
Cup Volume Control:	Yes
Flow Control:	Yes
Auto Shut Off:	Yes
Bypass Doser:	Yes
Pre-Infusion:	Yes
Low Water Warning:	Yes
Energy Saving Mode:	Yes
Descale Warning:	Yes
Multiple Programmability:	Yes
Pressure Gauges:	No
Brew Temp Display:	No
Brew Group
Material:	Plastic
Type:	Automatic
Removable:	Yes
Self-Cleaning:	Yes
Boiler Data
Number Of Boilers:	1
Brew And Steam Simultaneously:	No
Rapid Steam:	Yes
Type:	Thermoblock
Wattage:	1400
Volume:	Low
Material:	Stainless Steel Lined Aluminum
Element Location:	External
Insulated:	No
Pump Data
Type:	Vibration
Max Pressure:	15 Bar
Self-Priming:	Yes
Grinder Data
Number Of Grind Settings:	5
Hopper Capacity:	8.8 oz.
Burr Type:	Flat
Burr Material:	Ceramic
Freshness Lid:	No
Details
Maintenance Alerts:	Yes
Country of Manufacture:	Romania
NSF Certified:	No
Recommended Application:	Home Use