Difference between revisions of "Rocket Espresso Mozzafiato Type V"

From Whole Latte Love Support Library

 
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
{{Description-Table
+
{{Getting-Started
|title        = Rocket Espresso Mozzafiato Type V
+
|brand = Rocket
|machine_image = [[File:Mozzafiato-type-v-front.jpg|400px|none]]
+
|machine_type = Prosumers
|manufacturer  = Rocket Espresso
+
|product_banner = [[File: Wiki_ProductPageBanner_1200x175_RocketMozzafiatto_v1.jpg|link=]]
|model_name    = Mozzafiato Type V
+
|product_page_title = Rocket Mozzafiato Type V
|type          = [[:Category:Prosumers|Prosumer]]
+
|page_type = set up
|buy_button    = Yes
+
|section1 = Install It
|button_size  = 400px
+
|anchor1 = Install
|button_link  = https://www.wholelattelove.com/rocket-espresso-mozzafiato-type-v
+
|section2 = Get it Good & Hot
 +
|anchor2 = Heating
 +
|section3 = Get a Handle on your Tamp
 +
|anchor3 = Tamping
 +
|section4 = Brew Better
 +
|anchor4 = Brew Better
 +
|section5 = Brew the Best You Can Brew
 +
|anchor5 = Brew Best
 +
|section6 = Preinfusion and You
 +
|anchor6 = Preinfusion
 +
|section7 = Get Frothing
 +
|anchor7 = Get Frothing
 +
|section8 = Froth Better
 +
|anchor8 = Froth Better
 +
|section9 = Frothing and Habits to Avoid
 +
|anchor9 = Frothing Mistakes
 +
|section10 = Steam & the Heating Sweet Spot
 +
|anchor10 = Steaming Temperature
 +
|section11 = Steam with Thermometers
 +
|anchor11 = Steam with Thermometers
 
}}
 
}}
==Basic Usage==
+
{{Set-Up-Content
 
+
|dual_boiler =  
{{#ev:youtube|https://www.youtube.com/watch?v=oxXtDwkr9lM|480|center}}
+
 
+
===Adjusting Brew Pressure===
+
 
+
{{#ev:youtube|https://www.youtube.com/watch?v=KJwq4wR8vds|480|center|||start=343}}
+
 
+
===Draining The Boiler===
+
 
+
{{#ev:youtube|https://www.youtube.com/watch?v=ln25nJbyQQc|480|center}}
+
 
+
===Removing The Case===
+
 
+
Instructions for removing the casing of the machine can be found in the video below. The machine pictured in the video is slightly different than the R 60V, but the procedure is identical for most Rocket Espresso machines.
+
{{#ev:youtube|https://www.youtube.com/watch?v=KJwq4wR8vds|480|center|||start=36}}
+
 
+
 
+
== Cleaning & Maintenance ==
+
 
+
{{Maintenance-Prosumer
+
|single_heat_exchange = Yes
+
|softener_info        = This machine has a water softener cartridge available. The water softener should be replaced every 3 months. Replacement filters can be purchased [https://www.wholelattelove.com/rocket-espresso-water-reservoir-filter here].
+
 
}}
 
}}
 
+
[[Category: Rocket Espresso]]
== Troubleshooting ==
+
===No Crema or Bad Tasting Shots===
+
 
+
{{Troubleshooting-No-Crema-Bad-Shots}}
+
 
+
 
+
===Difficulty Frothing===
+
 
+
{{Troubleshooting-Frothing}}
+
 
+
 
+
===Flow Issues===
+
 
+
The first place to start with any flow issue is cleaning the machine. Before going through these steps please make sure the machine is cleaned according to the [[#Cleaning & Maintenance|Cleaning & Maintenance]] section of this article.
+
 
+
{{Troubleshooting-Prosumer-No-Steam
+
|steam_gauge        = Yes
+
|vacuum_relief_instr = Instructions for cleaning the vacuum relief valve on Rocket style machines can be found in the video below: {{#ev:youtube|https://www.youtube.com/watch?v=KJwq4wR8vds|480|center|||start=524}}
+
|hls_reset_instr    = Instructions for resetting the high limit switches can be found below after the [[#Removing The Case|cover is removed]]. Make sure the machine is turned off and unplugged.
+
|pstat_adjust_instr  = [[#Removing The Case|Remove the cover]] of the machine and then follow the video instructions below which show how to adjust a Sirai style pressurestat: {{#ev:youtube|https://www.youtube.com/watch?v=KHFeX2VHu74|480|center}}
+
}}
+
 
+
{{Troubleshooting-Prosumer-Brew-Blocked
+
|grouphead_instr = Instructions for cleaning the grouphead can be found in the document below: [[File:ALL MODELS Cleaning and Backflushing Grouphead.pdf|250px|thumbnail|center|Group Cleaning Instructions]]
+
|backflush_instr = Instructions for backflushing the machine can be found in the video below: {{#ev:youtube|https://www.youtube.com/watch?v=k1Vkfj83uyg|480|center}}
+
}}
+
 
+
 
+
====No Flow At All====
+
 
+
*'''Note: There may be a kinked, broken, or loose line somewhere in the machine. Remove the top of the machine and take a look inside to look for any obvious issues.'''
+
 
+
{{Troubleshooting-Prosumer-No-Flow-At-All
+
|socket_style = Yes
+
|sensor_instr = The tank's level sensor is not compatible with reverse osmosis or zero waters because of their lack of mineral content. The sensor depends on minerals being in the water to pass an electrical signal which tells the machine that water is present in the tank. Waters that don't have enough mineral content will not be able to pass this electrical signal, so the machine will not think water is present.
+
}}
+
 
+
===Machine Is Leaking===
+
 
+
{{Troubleshooting-Prosumer-Bad-Gasket
+
|gasket_instr = Instructions for replacing the gasket can be found in the document below: [[File:ALL MODELS Changing The Group Gasket.pdf|250px|thumbnail|center|Gasket Changing Instructions]]
+
}}
+
 
+
{{Troubleshooting-Prosumer-E61-Leak
+
|lever_style              = Lever
+
|lever_leak_instr        = A blowout of the lever assembly can be seen on p.6 of the machine's parts diagram. The o-rings that will need to be checked are listed as part 7 and part 14, and the valve assembly listed as part 11.
+
###To access these o-rings remove the end cap of the lever assembly using a flathead screwdriver.
+
###Once this is removed the other components of the grouphead assembly can begin to be slipped off. The bolts that the lever slides into can be removed with open ended wrenches or an adjustable wrench.
+
###Inspect the o-rings and make sure they are not damaged. It's possible that they are just dirty and need to be cleaned off and reseated. If they are damaged, broken, or shows signs of chaffing then they will need to be replaced.
+
###Inspect the valve components as well to make sure they are intact.
+
###Reassemble the components and see if leaking is resolved.
+
|top_valve_leak_instr    = A blowout of the top valve assembly, known as the mushroom or trumpet valve, can be found on p.6 of the machine's parts diagram. There are a few components which can be contributing to the leaking. There are two o-rings, listed as parts 2, 6, and 7 on this page of the diagram. There is also a valve assembly shown as part 9 on the same page.
+
###To access these parts use an open ended wrench or adjustable wrench to remove the smaller top bolt of the E-61. This will give you access to the first o-ring and spring assembly.
+
###To access further down into this part of the grouphead use a wrench to remove the large bolt. This will let you access the other o-ring, another spring assembly, and the other valve assembly.
+
###Inspect all of these components for integrity. Clean any dirty parts and replace any broken parts.
+
###Reassemble the grouphead and see if the leaking is resolved.
+
|bottom_valve_leak_instr  = A blowout of the bottom valve assembly, known as the release valve, can be found on p.6 of the machine's parts diagram. There are two o-rings in this assembly, listed as parts 7 and 31 on the diagram, and two valve assemblies, listed as parts 25 and 28 on the diagram, that can be causing the leak.
+
###To access these parts use an open ended wrench or adjustable wrench to remove the smaller bottom bolt. You will be able to access part 31, the o-ring, and part 28, one of the valve assemblies. Inspect the parts. If they are dirty clean them off, if they are broken replace them.
+
###To access the next o-ring and valve assembly use a wrench to remove the larger of the bolts. Again, inspect the parts for cleanliness and damage. Clean or replace as needed.
+
###Reassemble the release valve and test to see if the leaking is resolved.
+
|E61_group_cleaning_instr = Instructions for cleaning the entire E-61 can be found by clicking [http://coffeetimex.wikidot.com/e61-group-servicing here].
+
|E61_attach_instr        = There are two possible reasons for the machine to be leaking from here.
+
##The first is that one of the plumb lines connected to the back of the E-61 is not secure resulting in a leak. This will need to be tightened from the inside of the machine. You may see leaking from the bottom of the machine as well if this is the case. Remove the top of the machine and look towards the front of the machine. These lines will be located on the back of the faceplate, opposite to where the grouphead is seated. They are listed as parts 6 and 21 on p.8 of the machine's parts diagram. Use an open ended wrench or adjustable wrench to tighten these down. If the leaking persists you may need to apply white teflon plumbers tape or a sealing compound such as food safe permabond.
+
##The other possibility is that the E-61 group chassis gasket is not sealing tightly, or is worn out or damaged and will need to be replaced. The chassis gasket is listed as part 10 on p.6 of the parts diagram. There are two bolts which secure the E-61 to the machine chassis, causing it to press on the gasket and create a seal. The bolt assemblies are located behind the grouphead on the inside of the machine. Try tightening these two bolts down; if tightening these bolts does not resolve the leak, then the chassis gasket will need to be replaced.
+
}}
+
 
+
{{Troubleshooting-Prosumer-Bottom-Leak
+
|plumbed          = Yes
+
|water_source      = Reservoir
+
|level_probe_instr = Instructions for removing the level probe for cleaning can be found in the video below. Once the probe is removed use a scrubby sponge to clean any scale build up on it. Soaking the tip of the probe in a solution of hot water and backflushing powder may help with removing the buildup. Please note that the Rocket machine in the video has a different boiler orientation, but they use the same probe. The boiler in the Giotto is horizontally positioned, with the probe still located on top. The probe is listed as part 15 on p.8 of the machine's parts diagram. {{#ev:youtube|https://www.youtube.com/watch?v=WqBSfikYp7U|480|center|||start=135}}
+
|drain_line        = Yes
+
}}
+
+
{{Troubleshooting-Prosumer-Top-Steaming
+
 
+
}}
+
 
+
{{Troubleshooting-Prosumer-Wand-Leak
+
|tip_instr          = Unscrew the tip that is leaking and check the o-ring that seals the tip to the wand. Make sure all of the parts are clean and that the o-ring isn't damaged or broken. The metal steam  or hot water tips can be soaked in a solution of hot water and backflushing powder for more effective cleaning.
+
|ball_joint_instr  = <br />
+
##These instructions apply to both the steam and hot water wands. First remove the wand arm. This can be done by unscrewing the hex shaped nut at the top of the arm using an adjustable or open-ended wrench.
+
##Once the wand is removed you may have parts stick to the valve assembly. Do not lose these parts. A blowout of both wand assemblies can seen on p.10 of the parts diagram.
+
##There are a few different o-rings in this assembly. Make sure everything is clean and that the o-ring aren't damaged or broken.
+
##Inspect the tension spring, listed as part 10 on p.10, to make sure it is in good condition. The spring should be really firm. If it is easily compressed then it may need to be replaced. The bottom of the spring will have a metal gasket, which helps the wand pivot on the spring Make sure these parts are clean and reinstall them.
+
}}
+
 
+
 
+
===Machine Not Heating Or Powering On===
+
 
+
{{Troubleshooting-Prosumer-No-Power}}
+
 
+
{{Troubleshooting-Prosumer-Brew-Cold
+
|hls_instr            = Instructions for resetting the high limit switches can be found below after the [[#Removing The Cover|cover is removed]]. Make sure the machine is turned off and unplugged.
+
}}
+
 
+
{{Troubleshooting-Prosumer-Steam-Cold
+
|steam_test_instr      = Instructions for doing a steam test for the machine can be found in the video below: {{#ev:youtube|https://www.youtube.com/watch?v=iM_kVx-Fr3M|480|center}}
+
|hls_instr            = Instructions for resetting the high limit switches can be found below after the [[#Removing The Cover|cover is removed]]. Make sure the machine is turned off and unplugged.
+
}}
+
 
+
{{Troubleshooting-Prosumer-No-Heat
+
|tank_instructions = The tank's level sensor is not compatible with reverse osmosis or zero waters because of their lack of mineral content. The sensor depends on minerals being in the water to pass an electrical signal which tells the machine that water is present in the tank. Waters that don't have enough mineral content will not be able to pass this electrical signal, so the machine will not think water is present, and will not heat as a result.
+
|hls_reset_instr  = Instructions for resetting the high limit switches can be found below after the [[#Removing The Cover|cover is removed]]. Make sure the machine is turned off and unplugged.
+
}}
+
+
===Portafilter Handle Not Fitting On Machine===
+
 
+
{{Troubleshooting-Prosumer-Portafilter}}
+
 
+
==Diagrams & Manuals==
+
 
+
{{Support-Documents
+
|title              = Rocket Espresso Mozzafiato Type V
+
|parts_diagram      = [[File:Appartamento_Parts_Diagram.pdf|150px|none]]
+
}}
+
 
+
==Specifications==
+
 
+
{{Specifications-Prosumer
+
|basic_specs              = yes
+
|width                    = 10.78 in.
+
|height                  = 14.17 in.
+
|depth                    = 16.73 in.
+
|weight                  = 44.09 lbs
+
|watts                    = 1200
+
|volts                    = 120
+
 
+
|housing                  = yes
+
|housing_material        = Stainless Steel
+
|drip_tray_material      = Stainless Steel
+
|drip_tray_cover_material = Stainless Steel
+
|drip_tray_capacity      = N/A
+
|power_cord_length        = N/A
+
 
+
|frothing                = yes
+
|wand_material            = Stainless Steel
+
|wand_style              = Commercial
+
|wand_movement            = Articulating
+
|no_burn_wand            = Yes
+
|optional_tips            = Yes
+
 
+
|water_source            = yes
+
|source_type              = Reservoir & Plumbed
+
|reservoir_capacity      = 84.53 oz.
+
|reservoir_material      = Plastic
+
|reservoir_removable      = Yes
+
 
+
|controls                = yes
+
|control_type            = Lever
+
|display_type            = N/A
+
|pre_infusion            = Yes
+
|low_water_warning        = Yes
+
|pressure_gauges          = Brew & Steam
+
 
+
|cup_warmer              = yes
+
|warmer_material          = Stainless Steel
+
|warmer_size              = 10 x 9 in.
+
|warmer_type              = Passive
+
 
+
|portafilter              = yes
+
|portafilter_material    = Chrome Plated Brass
+
|portafilter_type        = Commercial Style
+
|quantity_included        = 1
+
|portafilter_weight      = 1.25 lbs
+
|portafilter_diameter    = 58 mm.
+
|commercial_baskets      = Single & Double
+
|bottomless_portafilter  = Yes
+
|tamper_size              = 58 mm.
+
 
+
|brew_group              = yes
+
|group_material          = Chrome Plated Brass
+
|group_type              = E61
+
|preheat                  = Yes
+
|solenoid                = Manual
+
|back_flushable          = Yes
+
 
+
|boiler_data              = yes
+
|num_boilers              = 1
+
|brew_steam_simultaneous  = Yes
+
 
+
|brew_boiler              = yes
+
|brew_boiler_type        = Heat Exchanger
+
|brew_boiler_wattage      = 1200
+
|brew_boiler_volume      = 1.8 Liter
+
|brew_boiler_material    = Copper with Brass End Plates
+
|brew_boiler_orientation  = Horizontal
+
|brew_element_location    = Internal
+
|brew_boiler_autofill    = Yes
+
 
+
|steam_boiler            = yes
+
|steam_boiler_type        = One Boiler for Brew and Steam
+
 
+
|pump_data                = Yes
+
|pump_pressure            = 18 Bar
+
|pump_pressure_adjust    = Yes
+
|pump_deairator          = Yes
+
|pump_self_prime          = 8-9 Bar
+
 
+
|performance              = Yes
+
|recommended_heat_up      = 900 secs
+
 
+
|details                  = yes
+
|manufacture_country      = Italy
+
|recommended_application  = Home / Commercial
+
}}
+
+
<!-- Categories -->
+
[[Category:Prosumers]]
+
[[Category:Rocket Espresso]]
+

Latest revision as of 13:21, 8 August 2018

Rocket Mozzafiato Type V

Wiki-NavIcons-NewUser Selected.jpg
Wiki-NavIcons-Clean-Maintenance.jpg
Wiki-NavIcons-Troubleshooting.jpg
Wiki-NavIcons-Diagrams.jpg






Install It

  1. Find a swanky spot in your home for your new machine to live, preferably where the morning sun can strike the mirror-finished housing so you can fully appreciate the bright idea that is your purchase.
  2. Get the power cord and the accessories out of the box.
  3. Plug the machine directly into an outlet. Don't plug it into surge protectors, extension cords, or timers.
  4. Fill the water tank.

Get it Good & Hot

It's time to get heated.

  1. Turn on the machine.
  2. Lock the portafilter into the group head.
  3. Wait 30 minutes.
  4. Take this time to start reading up on how to brew and froth below, if this is your first machine or you're new to pulling shots.
Heating Prosumer Image.jpg



Get a Handle on your Tamp

  1. Level off the grounds in your portafilter
  2. Keep your tamper level with the basket
  3. Apply consistent force downward, evenly, and level with the portafilter
    • 30 lbs. of pressure is a good rule-of-thumb to follow for beginners
Wiki-YT-HowToTampEspresso.jpg

How To: How Do You Tamp for Espresso?



Brew Better

  1. Lock the portafilter into the brew group.
  2. Lift the brew lever all the way up.
    • Aim for 2 to 2.5 oz. in about 25 seconds.
  3. Drink your shot to test.
  4. Repeat until properly motivated to get work done.


The big secret to finding that exact flavor you're after, that big punch-in-the-mouth feel, is dialing in your grind. For a basic rule-of-thumb, a coarser grind makes for a lighter, fluffier coffee, and a finer grind makes for a more intense, flavorful espresso. Check out the video on the right for more info.

Wiki-YT-BasicEspressoTechnique-DialingGrindSize.jpg

How To: Basic Espresso Technique - Dialing in Grind Size



Brew the Best You Can Brew

For more control, you'll want to know about how brew ratios and weighing your shots can help you keep a recipe so you can repeat your favorite results. Brew rations and weighing take all the guesswork out of the process so you always know what you're going to get.

Wiki-YT-HowToBasicRatiosAndWeight.jpg

How To: Basic Espresso Technique - Brew Ratios & Weight



Preinfusion and You

You can think of preinfusion is sort of a special trick to help bring out the best flavor in your coffee just before extraction. The idea is to softly wet the grounds before pressure is exerted by the pump.

  1. Bring the brew lever to a 45 degree angle. You will feel it stop there.
  2. Lift the lever slightly higher. This will allow for water to flow, but with no pressure from the pump.
  3. Lift the lever fully when satisfied and you're ready to brew.
Wiki-YT-HT Pre-Infusion E61 Brew Group 660x338.jpg

Pre-infusion on the Expobar Brewtus IV Espresso Machine


Get Frothing

If you like cappuccinos, lattes, Flat Whites, and other milk drinks, you're gonna need to know how to froth.

Wiki-YT-MilkFrothingforBeginners.jpg

Milk Frothing for Beginners



Froth Better

For a few quick tips to improve your frothing technique, check out the video on the right. You'll learn a few tricks to make your drinks even better.

Wiki-YT-5BasicTipsForFrothingMilk.jpg

Quick Tip: Five Basic Tips for Frothing Milk



Frothing and Habits to Avoid

Frothing can be a delicate process. There's a number of mistakes you can make that really bring down the quality of your drinks. Check out the video on the right to learn some easy things you can avoid going forward.

Wiki-YT-6CommonMilkFrothingMistakes.jpg

Quick Tip: Six Common Milk Frothing Mistakes



Steam & the Heating Sweet Spot

The literal sweet spot for steaming milk falls between 140°F and 155°F, with smaller drinks on the lower end and larger drinks on the higher end. A quick rule-of-thumb we follow is to steam just until the frothing pitcher becomes a little too hot to hold comfortably.

Wiki-YT-WhatIsTheBestTempForLatteMilk.jpg

What is the Best Temperature for Latte Milk?



Steam with Thermometers

If you're using a thermometer, you'll want to learn about lag time and how to read a frothing thermometer to correctly gauge the steaming process.

Wiki-YT-HowToUseAThermometer.jpg

How to Use a Thermometer When Frothing Milk for Latte and Cappuccino